WigJig Jewelry
Tool Kit
(Item 4000) |
Our WigJig Jewelry Tool Kit has the four basic tools required
for making jewelry by hand in a convenient nylon wallet. The
items included in this kit are our round nose pliers (Item
4001), our bent chain nose pliers (Item
4002), our chain nose pliers (Item
4007) and our economy cutter (Item
4006) in our vinyl wallet (Item
4008). Three of these tools are permanent tools that
we use ourselves every day. The economy flush cutter is an
inexpensive tool and we recommend that you will ultimately want to
replace this tool with our Flush Cutter Ultra (Item
0356).
Not included in the kit, but also tools that a beginner will
want are our fine step jaw pliers (Item
4003), nylon jaw pliers (Item
4004), and bent closing pliers (Item
4005). These tools are shown below.
|
WigJig Round
Nose Pliers
(Item 4001) |
These round nose pliers provide smaller, finer tips allowing
you to make small and delicate wire components. The jaws are
16mm long. These shorter jaws have less twist when making loops close to the tips
and therefore allow making smaller loops more consistently..
At the tips, the jaws are slightly less than 1mm wide. This allows you to make smaller loops consistently. We
believe that these round nose pliers provide the best
functionality available at any price. These pliers are 5"
long.
(New Low Price! Formerly $17.95.)
|
WigJig Bent
Chain Nose Pliers
(Item 4002) |
These bent chain nose pliers have a tip that is 1mm wide.
We believe that this narrow tip is important when grasping a loop
to make a wrapped loop. The jaws of these pliers are
approximately 28mm long. Just like the round nose pliers
above, we believe that these pliers provide the best functionality
available at any price. These pliers are 5 1/2" long.
(New Low Price!
Formerly $21.95)
If this item is
out of stock, we suggest that you consider item 2828 here.
|
WigJig Fine
Step Jaw Pliers
(Item 4003) |
These pliers make loops of defined sizes without marking the
wire on the outside of the loop. This is because the flat
jaw on the pliers spreads the gripping force and does not mark
the wire. The first step is 1/16", the size
of the peg for the WigJig Delphi, Cyclops and Centaur. The
second step is 3/32" the size of the peg for the WigJig Olympus, Olympus Lite or Electra.
The third step is 9/64". The jaws of these pliers are 27mm
long. If you want to reduce tool marks on your
jewelry, we strongly recommend this tool. We make the
initial loop on every piece of jewelry that we make using
these tools. These pliers are 5 1/2" long.
(New Low Price!
Formerly priced at $14.85)
If this item is
out of stock. We suggest that you consider our item 2774
here.
|
WigJig Nylon
Jaw Pliers
(Item 4004) |
We use nylon jaw pliers for straightening wire before we use
it to make a jewelry component and for flattening and hardening
the wire component after we have shaped it on one of our WigJig
jewelry tools. These pliers are 5 1/2" long.
(New Low Price!
Formerly priced at $19.95)
|
WigJig Loop
Closing Pliers
(Item 4005) |
These pliers are used for closing a small opening in a loop
without marking the wire. There are grooves in the face of
the jaws of these pliers. These grooves allow you to grip
the sides of a loop in a piece of wire without having the wire
slip. Then you can gently squeeze the loop to close any gap.
These pliers are 5" long.
New low price!
|
WigJig Economy
Flush Cutter
(Item 4006) |
Economy Flush Cutter. This cutter is an inexpensive
flush wire cutter. We don't recommend this cutter for
serious wire workers. We recommend our Flush Cutter Ultra (Item
0356) for serious wire workers. These pliers are
designed for beginners to making jewelry with wire and beads.
This cutter is 5" long.
|
WigJig Chain
Nose Pliers
(Item 4007) |
These straight chain nose pliers have flat smooth jaws for
grasping and holding wire. They make a great second pair of
chain nose pliers for someone who has already purchased our best
chain nose pliers, the bent chain nose pliers shown above.
These pliers are 5" long.
|
WigJig Jewelry
Tool Wallet
(Item 4008) |
WigJig Vinyl Wallet with 8 pockets for holding your jewelry
making tools. This jewelry tool wallet is 7 1/2" tall and 14
1/2" long.
|
